The No Entry sign indicates that no vehicles are permitted to enter the road from this direction. It is typically placed at the exit of one-way streets to prevent vehicles from entering against the flow of traffic. Ignoring this sign can lead to serious accidents or traffic violations.

The No Stopping sign means that drivers are not allowed to stop their vehicle at all, not even briefly, for any reason—unless directed by a police officer or in an absolute emergency. This rule helps prevent traffic congestion and ensures clear passage, especially in high-risk or high-speed zones like tunnels, bridges, or intersections.

The No Entry for Buses sign indicates that buses are prohibited from entering the road beyond this point. It’s often used on narrow or residential roads where large vehicles could cause congestion or pose a danger.

When encountering a tractor traveling slowly on a busy road, other vehicles may become impatient and attempt to overtake. You should expect that one of the vehicles behind the tractor might suddenly move into your lane to overtake, especially if the tractor is traveling slowly. Always stay alert and be prepared for sudden movements from other drivers, particularly in areas with limited visibility.

When approaching a roundabout in Ghana, you should always give way to traffic on your left, as traffic flows on the right side of the road. This helps maintain a smooth and safe flow of vehicles around the roundabout.

On a freshly graveled road, loose stones can reduce traction and increase stopping distances. Vehicles overtaking you can kick up gravel, which may damage your windshield or reduce visibility. Additionally, sudden maneuvers on loose gravel can lead to skidding. It’s important to reduce speed, maintain a safe following distance, and be extra cautious of vehicles overtaking to avoid accidents.

Taking up the correct position in good time signals your intentions to other road users, allowing them to anticipate your movement and adjust accordingly. This improves road safety and ensures smoother traffic flow. Proper positioning also helps prevent last-minute lane changes, which can be dangerous.

Leaving both parking and hazard lights on make your vehicle more visible to other drivers and pedestrians, especially in poorly lit areas, thus reducing the risk of accidents. 

Before moving off, a driver must check their surroundings, look into the mirrors, and signal their intentions. This ensures awareness of other vehicles, pedestrians, and any potential hazards, improving safety for everyone on the road.

Road humps are designed to slow down traffic and improve safety. Driving too fast over them can damage your vehicle and make the ride uncomfortable. It's important to maintain a reduced speed at all times, not just during school hours.

Before overtaking a long vehicle, you should:

1. Signal your intention to let other road users know your move.
2. Use your horn (if necessary) to alert the driver of the long vehicle, especially if they might not see you due to blind spots.
3. Ensure the road ahead is clear and that it’s safe to overtake.
4. Execute the maneuver quickly and safely, returning to your lane smoothly.

When driving a slow-moving vehicle on a narrow winding road, it's important to pull in safely when possible, allowing faster vehicles to overtake. This helps prevent traffic buildup and ensures safer driving conditions for everyone.

You can tell if your vehicle's tires are losing grip on a wet road by:

• Feeling the steering wheel become unresponsive or loose: If the tires lose grip, the steering may feel less connected to the road, making it hard to control the vehicle.
• Hearing a sloshing or splashing sound: If the tires start hydroplaning, you may hear water being displaced.
• The vehicle starts to skid or slide: If the tires lose grip, your vehicle may slide or skid, especially when braking or turning.
• The car feels like it’s drifting: You may feel the car start to drift or slide sideways even with gentle steering inputs.

The battery indicator light on the instrument panel warns of a potential issue with the vehicle's charging system. It could mean a failing battery, a faulty alternator, or a problem with the electrical system. If this light stays on while driving, the vehicle may lose power, and immediate inspection is recommended.

If the brake fluid level gets too low, it can affect the performance of the braking system, leading to brake failure or reduced braking efficiency. This significantly increases the risk of a crash, as you might not be able to stop the vehicle when needed.

While other fluids like antifreeze, radiator coolant, and battery water are important for engine function, they are less likely to directly cause a road crash if their levels get low, although engine overheating or electrical issues can still pose risks.

A properly serviced vehicle runs more efficiently, which can improve fuel economy and overall performance. Regular maintenance, such as oil changes, tire checks, and engine servicing, helps the vehicle operate at its best.

Hazard warning lights should be used when you are stopped in an emergency to alert other drivers of a potential danger. They help warn others to proceed with caution.

Hazard lights are not used to thank other drivers, When parking briefly, or when overtaking. Their purpose is specifically to signal an emergency or a hazard on the road.

For towing a vehicle, it’s best to use a metal bar rather than a rope or conveyor chain, as it provides better control and safety for both vehicles. A strong metal bar is a safer and more secure method for towing, especially on major roads.

The correct answer is "Triangular signboards."

Warning road signs are typically triangular in shape with a red border. They are used to alert drivers of potential hazards ahead, such as sharp bends, pedestrian crossings, or animal crossings.

• Circular signboards are usually used for regulatory signs, such as speed limits and no-entry signs.
• Rectangular signboards are generally used for informational signs, like road directions and place names.
• Square signboards are less common but are sometimes used for special information signs.

Therefore, warning road signs are indicated on triangular signboards.

You should avoid using your horn when stationary, except if there is an immediate danger from a moving vehicle. The horn is meant to warn others of potential hazards, not to express frustration or announce your arrival.

When you’re undergoing a practical driving course, you are typically required to display L plates (learner plates) on the vehicle. This alerts other road users that you are a learner driver and may need extra consideration. You should also always be accompanied by an instructor or a qualified supervising driver during the lessons.

The indicated sign is Roundabout Coming Up.

Roundabout Coming Up indicates a circular intersection ahead. Drivers must give way to traffic already in the roundabout and follow the circular flow.

This is a Blind Pedestrian Crossing sign

It alerts drivers that visually impaired pedestrians may be crossing the road ahead. Drivers should slow down and be prepared to stop if necessary.

The road sign shown indicates a Sharp Reverse Curve To Left.

A "Sharp Reverse Curve to Left" sign warns drivers of two sharp bends ahead-first to the left, then immediately to the right. Drivers should slow down and navigate carefully.

The road sign shown indicates a Sharp Reverse Curve to Right.

A "Sharp Reverse Curve to Right" sign warns drivers of two sharp bends ahead-first to the right, then immediately to the left. Drivers should slow down and navigate carefully.

The correct answer is "Turn Right".

This sign means you must turn right when you get to the junction. You can’t go straight or turn left — right turn only.

The correct answer is "Priority Over Vehicle From Opposite Direction".

This sign means that vehicles on this road have the right-of-way over others entering or crossing it. But even with this advantage, drivers should still stay alert and exercise caution — not everyone might notice or obey the sign.

The correct answer is "Turn Left".

This sign means you must turn left when you reach the junction. You can’t go straight or turn right — left turn only.

The correct answer is "No Through Road on Left".

This sign means the road on your left doesn’t go through. Only turn left if you really need to.